Axiohm A758 Bedienerhandbuch Seite 42
- Seite / 217
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
A758 Owner’s Guide Chapter 3: Using the Printer
September 1999 36
Check Flip Test Mode
To run the Check Flip Test Mode:
1.
Enable the Check Flip Test Mode through the Configuration Menu (See
“Configuring the Printer,” for instructions on how to enter the Configuration
Menu), then exit the Configuration Menu.
2.
Insert a check as if validating the check, lengthwise and face down into the
slip station. (See “Verifying and Validating Checks” section to insert check.)
A check must be used—if any other slip or form is inserted the printer will
not conduct the test.
Extended
Slip Table
Slip
Table
Check
Guide
Green
Slip-in LED
First Line of
Print Guide
Check Orientation - Face down
ENDORSE HERE
MEMO
3.
Push Paper Feed Button.
The check then goes through the flip routine only—no printing takes place.
To exit the Check Flip Test Mode:
1.
Enter the Configuration Menu again.
2.
Disable the Check Flip Test Mode.
3.
Exit the Configuration Menu.
The printer is in Normal Mode and can communicate with the host
computer.
- Owner’s Guide 1
- Legal Notices 2
- A758 Owner’s Guide 3
- September 1999 3
- Contents 4
- Chapter 1: About the Printer 7
- Introducing the A758 Printer 8
- Standard Features 9
- Thermal Receipt Printer 10
- Impact Slip Printer 10
- Connectivity Options 11
- Impact Slip Printer Options 11
- Model Identification Key 12
- Chapter 2: Setup Guide 13
- Unpacking the Printer 14
- Choosing a Location 15
- Remove the Packing Restraints 16
- Connecting the Cables 18
- Cash Drawer Cables 19
- Power Supply Cable 19
- Loading Receipt Paper 20
- Testing the Printer 22
- Chapter 3: Using the Printer 24
- Printer Controls 25
- Changing the Receipt Paper 26
- Replacing the Ribbon Cassette 27
- Printing on Forms or Checks 29
- PAY TO THE 30
- ORDER OF 30
- ENDORSE HERE 31
- Check Flip 33
- Window Door 33
- Printer Configuration 36
- Configuring the Printer 37
- Communication Interface 39
- Diagnostic Modes 39
- Receipt Test Mode 40
- Slip Test Mode 40
- MICR Test Mode 41
- Check Flip Test Mode 42
- Emulation/Software Options 43
- Hardware Options 43
- Knife Option 44
- Paper Low Sensor 44
- Printhead Resistance 44
- MICR Option 44
- Check Flip Option 44
- Basic Troubleshooting 45
- Printer Beeps 46
- Printer Will Not Print 47
- Poor Forms Print Quality 49
- Poor Receipt Print Quality 50
- Knife Does Not Operate 52
- Other Serious Problems 53
- Returning a Printer 54
- September 1999 50 56
- Ordering Thermal Paper 57
- Ordering Parts and Supplies 58
- Ordering Communication Cables 59
- Forms Specifications 59
- Check Specifications 59
- Ordering Ribbon Cassettes 60
- Ordering Extended Slip Tables 61
- Ordering Documentation 61
- September 1999 56 62
- Functional Description 63
- Slip Forms - Recommendations 64
- Standard Receipt Features 66
- Character Sets 67
- Graphics 67
- Bar Code Fonts 67
- Optional Features 68
- Reliability 69
- Certifications 70
- Temperature and Humidity 71
- Electrical 71
- Slip Media 72
- Receipt Media 72
- Migration 73
- Performance Requirements 74
- Slip Throughput 75
- Character Format 76
- Receipt Printing 77
- September 1999 73 79
- Receipt Throughput: 80
- Partial Cut Knife 80
- Receipt Paper Low: 81
- Interface Description 82
- September 1999 77 83
- Power Requirements 84
- Electrical Interfaces 84
- Switch Settings 85
- Code Page 437 86
- Code Page 850 87
- Code Page 852 88
- Code Page 858 89
- Code Page 860 90
- Code Page 863 91
- Code Page 865 92
- Code Page 866 93
- Dimensions and Weight 94
- September 1999 89 95
- Communication Overview 96
- RS-232C Interface 97
- RS-232 Communications 98
- XON/XOFF Protocol 99
- DTR/DSR Protocol 99
- Connector Pin-outs 100
- Power Connector 101
- Cash Drawer Connector 101
- Parallel Interface 102
- Chapter 7: Programming Guide 103
- Command Conventions 104
- List of Commands and Location 105
- By Function 109
- Print Characteristic Commands 111
- Graphics Commands 112
- Status Commands 112
- Barcode Commands 113
- Page Mode Commands 113
- Macro Commands 113
- MICR Check Reader Commands 113
- Check Flip Commands 114
- User Data Storage Commands 114
- Flash Download Commands 114
- Comparison to A756 115
- Comparison Chart 117
- Command Descriptions 118
- Close Form 119
- Open Form 119
- Perform Full Knife Cut 119
- Perform Partial Knife Cut 120
- Generate Tone 120
- Return Home 120
- Initialize Printer 121
- Set Slip Paper Eject Length 121
- Bit Function 123
- Set Slip Paper Waiting Time 124
- Select Slip Station 125
- Select Cut Mode and Cut Paper 125
- Select Receipt Station 126
- Print Test Form 126
- Print and Feed Paper One Line 127
- Print and Eject Slip 127
- Print and Carriage Return 127
- Extra Dot Rows 129
- Set Line Spacing to 1/6 Inch 130
- Set Line Spacing 130
- Print and Feed Paper 130
- Reverse Feed 132
- Horizontal Tab 133
- Set Column 133
- Set Horizontal Tabs 135
- Set Relative Print Position 135
- Select Justification 137
- Set Left Margin 138
- Set Printing Area Width 139
- Select Pitch (Column Width) 141
- Select Print Modes 142
- Select Double Strike 146
- Cancel Double Strike 147
- Select or Cancel Italic Print 147
- Select Character Code Table 148
- Select Character Size 149
- Summary of Rotated Printing 151
- September 1999 148 154
- Define Downloaded Bit Image 156
- Print Downloaded Bit Image 158
- Batch Mode 161
- Status Byte (RS-232C) 162
- Value of 164
- ASC Hex Dec 164
- ASCII HEX 169
- Real Time Commands 170
- Auto Status Back 177
- Bar Code Commands 181
- Print Bar Code 182
- Select Bar Code Width 184
- Print Data in Page Mode 186
- Select Page Mode 186
- Select Standard Mode 187
- Execute Macro 193
- MICR Commands 194
- Modifiers 195
- Selector Comments 195
- Status Status Byte Value 198
- Bits within Byte 201
- Check Flip Command 203
- Flash Allocation 206
- Erase User Flash Sector 207
- Get Firmware CRC 209
- Return Microprocessor CRC 210
- Erase the Flash Memory 210
- Return Main Program Flash CRC 210
- Erase Selected Flash Sector 210
- Reboot the Printer 211
- A758 Owner’s Guide Index 212
- September 1999 206 212
- September 1999 207 213
- September 1999 208 214
- September 1999 209 215
- September 1999 210 216
- A758-D100 189-9200246 A 217
- © 1999 AXIOHM 217
- Printed in U.S.A 217
Verwandte Produkte und Handbücher für Drucken & Scannen Axiohm A758
Drucken & Scannen Axiohm 7156 Spezifikationen
(36 Seiten)
(36 Seiten)
Drucken & Scannen Axiohm Astrium Spezifikationen
(14 Seiten)
(14 Seiten)
Drucken & Scannen Axiohm 7193 Spezifikationen
(84 Seiten)
(84 Seiten)
Drucken & Scannen Axiohm 7193 Spezifikationen
(104 Seiten)
(104 Seiten)
Drucken & Scannen Axiohm 7156 Spezifikationen
(314 Seiten)
(314 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern